E706 on a Fisher & Paykel top loader is described here as a controller or low-mains fault, so the first question is whether the washer had a power problem or the control electronics did. Check that the washer is getting steady power, use the manufacturer’s single power-off reset for your model, and book diagnosis if the code comes back. The global top-loader guide for some models does not define E706 in its text, so your own manual decides what applies.
A Fisher & Paykel fault is most useful when it is tied to the right appliance family and exact model. This guide explains what to record, which owner-safe checks may be appropriate, and when the problem should move to professional diagnosis.
Quick Answer
On the applicable top-loader family, E706 is used in a controller/low-mains fault context. Record any obvious power event and the exact model, but do not treat the code as proof that a control board must be replaced without diagnosis.
Why the Exact Model Matters
Fisher & Paykel has used multiple generations of DishDrawer, ActiveSmart refrigeration, laundry and cooking platforms. Similar displays or code labels do not guarantee identical components or identical troubleshooting steps. Use the full model/product code whenever it can be read without disassembling the appliance.
A useful troubleshooting page should reduce uncertainty without pretending that a web page can confirm a failed part.
Symptom Guide
Because the label points at power or control rather than at a wash-path part, the pattern around the code says more than the code alone.
| Symptom | What it can point to | What you can safely check |
|---|---|---|
| Code shows after the lights flickered or the breaker tripped | A supply disturbance that the controller reacted to | Whether other appliances on the same circuit behaved oddly, and whether the breaker is fully on |
| Continuous beeping, control lights off, a number on the display | The fault mode that one global top-loader guide describes for several models | Touch any button to silence the beeping; the Power button can still turn the washer off |
| Code returns at the same point of every cycle | A repeatable condition tied to one stage rather than a one-time event | Which stage it is, and whether it happens with a small load as well |
What to Record Before You Reset Anything
- exact appliance family;
- full model/product code from the rating label if accessible;
- complete code, alert or indicator pattern;
- the cycle, mode or operating state when the problem appeared;
- whether the symptom is constant or intermittent;
- any recent installation, plumbing, power, network or use change that clearly preceded the issue.
A photo of the display and model label is often more useful than a long guess about the failed part.
What does a top-loader fault mode look like?
One global guide for several Fisher & Paykel top-loader models describes the fault mode as continuous beeping, all control lights off and a fault number on the display. Touching any button silences the beeping. That is a different picture from a washer that simply pauses, so it helps to know which one you are looking at before deciding anything.
The same guide’s steps are to turn the washer off at the power point, wait one minute, turn it back on, remove the wash load and run a Rinse cycle. If the fault is still there after that, the guide hands the problem to a repairer. Check your own manual, because this guide is not a US edition and your model may word it differently.
Owner-Safe Checks
Use only the checks described for the exact model in Fisher & Paykel user/support documentation. Owner-safe actions normally stay at the level of accessible filters, visible supply conditions, control settings, door/drawer position, power state or other items the manufacturer explicitly exposes to the user.
Do not remove live electrical covers, open sealed refrigeration systems, bypass sensors or safety devices, force a locked oven door, perform gas-system work, or substitute a generic internet reset for a model-specific procedure.
When the Code or Symptom Needs Service
Request diagnosis when the fault returns after documented owner checks, when the appliance cannot complete its normal function, or when the issue involves internal electrical, heating, sealed-system, gas, pump/motor, control or safety-related diagnosis.
If there is smoke, sparking, a strong electrical smell, uncontrolled water leakage, abnormal overheating or another condition that may be unsafe, stop normal use and address the safety condition before routine troubleshooting.
What the Code Does Not Prove
An error code usually identifies a fault category or condition. It is not automatically proof that a specific sensor, board, valve, motor, compressor, heater or other component must be replaced. The repair decision should come after the actual appliance is checked in the correct model context.
How can you tell a power problem from a controller problem?
Begin with the supply: confirm the breaker is on and the plug is seated in a wall outlet. If E706 returns while power is steady, the washer needs diagnosis.
A low-mains label suggests the washer may have been starved of steady voltage, which can come from the outlet, the circuit it shares or the supply itself. Confirm the breaker is on and the plug is seated in a wall outlet rather than a loose adapter.
If power looks normal and E706 returns, the question moves inside the machine. That is the point to stop, since the controller is not owner territory.
Related Fisher & Paykel Repair Information
- Washer service guidance
- Fisher & Paykel model reference
- Fisher & Paykel error-code library
- Los Angeles & Orange County service areas
Preparing a Better Service Request
A concise request should include the appliance type, model code, exact symptom, displayed fault and service address. If the appliance still operates intermittently, describe what usually triggers the problem. If the issue appeared after installation, a move, plumbing work, a power interruption or a network change, include that detail without assuming it is the root cause.
Frequently Asked Questions
Can I use a troubleshooting step from a different Fisher & Paykel model?
Only when the manufacturer documentation explicitly covers both models. Otherwise treat procedures as model-specific.
Should I clear the code before I write it down?
Record the complete code or indicator state first whenever it is safe. Repeated resetting can erase useful context without fixing the underlying condition.
Can I order the suspected part from the symptom alone?
That is usually a poor first step. Similar symptoms can have different causes, and parts compatibility depends on the exact model/product code.
Does this site represent Fisher & Paykel?
No. This is an appliance repair resource and service site.
Is E706 the same thing as a power outage?
No. A power outage is an event, while E706 is the washer’s own fault display. The two can be linked, but the code can also appear with no outage you noticed.
Where do I find the serial number on a top loader?
The washer guide places it on the rear of the washer. You can read it there without opening anything.
Book Electrical Diagnosis
Use the booking form with the exact appliance, model code if available, symptom, displayed code and service address. Service availability should be confirmed before an appointment is promised.
Secondary context: official legacy manuals and product resources.
Technician-community reports may inform diagnostic hypotheses but do not replace manufacturer code definitions or safety guidance.
Keep reading
Similar articles
Fisher & Paykel Oven A2 or A3: Self-Clean Door Lock Faults
A2 on a Fisher & Paykel oven means the door could not lock after a Self Clean started, and A3 means it could not…
Fisher & Paykel Oven “F + Number” Fault: What to Do Next
An F plus a number on a Fisher & Paykel oven marks a technical fault. Let the oven cool and the fans finish, switch…
Fisher & Paykel Induction Cooktop Not Responding: Safe First Checks
When a Fisher & Paykel induction cooktop seems unresponsive, check whether the controls are locked, whether the screen has moisture or oil on it,…
Book a repair
Tell us what’s wrong — we’ll take it from there
Share a few details and we’ll confirm an appointment. Prefer to talk? Call us and we’ll help right away.
Request your repair
Fields marked with * are required.